A canvas or fabric awning is a big decor plus for an entry, patio or the first floor windows along one side of the house.

diy roll up awning

For a basic shade awning, the fabric cover is simply attached to the building over the window or doorway, and the draped or taut material is laced to a horizontal pole suspended parallel to the wall by two angled side supports.

Replacing or installing the awning involves weaving heavy cord or thin polyester rope through grommets along the front edge of the awning and around the parallel pole. Measure the front of the awning from edge to edge and multiply the length by 3. Cut a piece of thin rope or poly cord to this measurement. Pull the awning fabric over the parallel pole so it hangs down over the front of the pole.

Secure the fabric to the pole with large spring clips to hold it in place while you work. Stand under the awning, facing the parallel pole and the overlapping front end of the fabric. You will be lacing the awning to the pole using a stitched-on panel punctuated by grommets, visible on the underside of the awning. Some awnings may not have a front overhang and will just end in a reinforced hem with a line of grommets across it.

Starting at one side, tie the lacing cord to the first grommet with a secure knot. Then drop the long end of the cord behind the pole; bring it around the pole, up in front and through the front of the same grommet to make a loop. Pull the raw end of the cord between the pole and the cord on the underside of the pole, and tighten it to lock the cord in place and the corner of the awning to the pole.

Push the raw end of the cord through the next grommet, front to back, bring it down, under and up around the pole, and then continue lacing the cord through the grommets along the pole to the opposite end of the awning. Keep the cord tight enough to snug the awning fabric to the pole, but avoid bunching the fabric between grommets.

Reverse the locking procedure you used at the start of the restringing. At the last grommet, feed the raw end of the cord through the hole, front to back. Bring the end of the cord from behind the pole, under, up and over the pole, through the grommet again and behind the pole. Remove the spring clips, and adjust the cord tension so the awning lays flat along the parallel pole before you complete the restringing.

Poke the end of the cord between the pole and the cord wrapped around the pole. Bring it up and tie it off at the grommet in a secure knot. Trim any excess cord. Benna Crawford has been a journalist and New York-based writer since Crawford has a degree in theater, is a certified Prana Yoga instructor, and writes about fitness, performing and decorative arts, culture, sports, business and education. Skip to main content.

Things You Will Need Awning fabric with grommets Support structure for awning Tape measure Thin rope or cord Scissors or heavy shears 2 or more large spring clips Ladder optional. Tip To secure a broad awning, double-loop the cord through the grommet at the midpoint. Poke the cord front to back through the grommet; bring it around, under and up the front of the pole, catching the cord between the section of cord already lying along the awning and the pole.

Restring the cord through the grommet, front to back, once more, and continue lacing to the end of the awning. Warning Check the knots at either end of the pole to be sure they hold tightly before proceeding with the lacing, or trimming the end of the cord.

Customer Service Newsroom Contacts.They will allow you to enjoy your outdoor area in comfort during the hot summer months. For more of my top gear recommendations, have a look through these popular Outside Pursuits guide links: Patio UmbrellasPatio SwingsOutdoor Hammocks. Our reviews of the top rated retractable awnings with a comparison table and buyers guide will help you choose the right one for you.

Made with UV-and-water-resistant polyester as well as a powder-coated aluminum frame, you can rest assured this retractable patio awning will hold up in the elements with ease.

Aluminum is tough yet very lightweight, with the entire unit weighing just The easy crank handle is what lets you retract or extend the design, with a built-in reel and crank handle. This lets you extend or retract the awning, as well as adjust the pitch to block the sun throughout various times of the day! The frame is comprised of both steel and aluminum, which is just about the toughest combo you can get at this affordable price.

However, you should count on this model being notably heavier, weighing about 3x what the last product does! Are you on a budget but still want one of the best outdoor awnings currently out there? The cover is made with polyester fabric, complete with a PU waterproof coating to ensure it holds up well in both the sun and the rain.

The frame is made with thick aluminum and steel to further ensure durability even in heavy winds and extreme temperatures. While you can definitely use them on patios and porches, we found they were ideal to use above windows and doors due to the more narrow design. Unfortunately, you just get to choose from two color options, which are Red Wine or a darker forest Green.

We would like to see some more neutral colors added in the future, as not everyone likes these colors. Made up of both aluminum and steel, the frame will easily last you for years. The fabric consists of thick, polyester fabrics which feature a PU waterproof coating, much like with the previous product.

You can choose to use it by itself or without support arms, which are not included with the package. What it does include, are wall-mounting brackets made for quick and painless installation. In fact, you only get one: a white frame with burgundy fabric. In addition, the package comes with a one-year warranty. This is a manual retractable awning model that is easy to operate.

This is another model we felt worked perfectly installed above windows and doors, protecting you from the elements while helping keep your indoors cool on scorching days. The multi-surface installation method lets you connect the awning to an array of different surfaces such as siding and stucco.

If you are planning on mounting it to wood-framed homes, know that you will have to purchase the mounting screws separately. Comprised of thick polyester fabrics with a PU waterproof coating, you can easily use this model in various types of weather conditions.

DIY Roll Up Green Screen

This design also comes in a single color — Beige- but at least it meshes with practically any other color out there. The supporting wire cables and pad eyes make them easy to connect to an already-existing pergola or a new free-standing frame structure — whatever you prefer best.

By the end of it, you should know exactly which one is the perfect product for you and your needs. Make sure the one you have in mind works with the building you want to place it on, or you may have to send it back and get another! Try to pick a model just slightly larger than the area you have in mind.

The material of the awning is the next most important factor when making your selection. Canvas is usually comprised of cotton or linen, and occasionally hemp. However, it has the most tensile strength of most materials, aside from aluminum. PVC Is, in contrast to canvas, a synthetic material which is probably our least favorite material due to how quickly it breaks down.

In addition to that, it lacks the tensile strength other materials have, making it vulnerable to rips and tears. This is quite possibly the most commonly used material in patio awnings. Some companies go even further and layer on a PU-coating to make it even more resistant against UV rays!Roll up awnings are simple to use and very effective at shielding the elements.

As an added bonus, the material in roll up awnings can easily be swapped out to give a fresh look or added curb appeal to the house. As a decorative treatment they are durable and low maintenance coverings to go over doors, patios, decks and windows. Installing the awning can vary slightly from each manufacturer, but in general is a quick process. The help of an assistant can greatly ease large awning installation by holding up the other side of chalk lines, levels or mounting hardware.

Take out all the pieces and the instructions for you awning. Identify each piece, where it goes, and how it functions for the awning. Most all roll up awnings are simple machines when understood, but can be frustrating if malfunctioning some how. Since they will be mounted overhead, the best time to understand the mounting hardware and functioning of your awning is before it is installed.

Determine the height the awning should sit at to be of the most effective use. Taking into account where the sun and wind often come from can greatly help this process. When you think you have selected the best place, it is often helpful to have another person step back from the house to view the location from a distance. Since the awning is large, it can be difficult to get the big picture while attempting to mount it and even more frustrating to have to adjust the placement once mounted.

Once height is determined, snap a chalk line across the expanse the awning will be mounted against. Check the chalk line with a level before snapping to avoid confusion with multiple lines. Assistance holding one end of the chalk line can increase success with large expanses. Use the stud finder to locate the structural supports along the chalk line. Joists, headers and studs all work.

Once the studs have been found, use a fine drill bit to locate the outer edges of each stud by drilling small holes one inch below the chalk line. Use the outer edges to find the center of the stud and mark it with a long vertical line. Once found, fill all holes with silicone sealant. Use the mounting hardware provided and the instruction manual to decide exactly how far apart for the awning brackets to be placed.

Screw the brackets into the studs along the vertical lines designating center. Next, install the hood onto the mounting hardware. Insert the bar into the mounting hardware and secure with the washers and bolts provided with the awning.

Unroll the awning and adjust the pitch to the desired slope. Consider rain, snow, and wind when deciding on the angle of the awning because these elements can have large effects on the structure. We welcome your comments and suggestions. All information is provided "AS IS.

All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here. Toggle navigation Login Register How-Tos. How to Install a Roll-Up Awning. Written by Doityourself Staff. Needed Roll up awning Chalk line level stud finder Power drill Silicone Sealant Screwdriver Assistant optional Step 1 - Familiarizing Yourself Take out all the pieces and the instructions for you awning.

The 7 Best Retractable Awnings [2020 Reviews & Guide]

Step 2 - Deciding How High Determine the height the awning should sit at to be of the most effective use. Step 3 - Locate Studs Use the stud finder to locate the structural supports along the chalk line. Step 4 -Mounting Hardware Use the mounting hardware provided and the instruction manual to decide exactly how far apart for the awning brackets to be placed.Outdoor living spaces can add a lot of value to your home, not to mention all the extra space for entertaining, enjoying the beautiful summer weather, and just relaxing and taking a few minutes to yourself.

But if your backyard gets baked by the sun, you might find that a few minutes are all you want to spend out there! These nifty projects do more than just keep off the sun. Use shade panels to define outdoor seating areas, or add privacy from nosy neighbors around your pool or deck. Keep in mind that adjustable panels are the most useful; you can always remove or retract them if you decide you need more light, or if heavy wind threatens to damage them.

Ready to beat that sweltering summer heat? Check out these DIY backyard sun shade ideas that will have you spending your entire summer outdoors. DIY Project Details: housetweaking.

diy roll up awning

DIY Project Details: sailrite. DIY Project Details: sunset. DIY Project Details: awninglux. DIY Project Details: bobvila. DIY Project Details: instructables. DIY Project Details: thekreativelife. DIY Project Details: refinery DIY Project Details: lauratrevey. DIY Project Details: thriftyandchic. DIY Project Details: marthastewart.

DIY Project Details: anythingpretty. DIY Project Details: vtwonen. DIY Project Details: jandbmarvin. DIY Project Details: allyou. DIY Project Details: ebay. DIY Project Details: abeautifulmess. DIY Project Details: zodirowe. DIY Project Details: twoboysonegirlandacrazymom. DIY Project Details: remodelaholic. DIY Project Details: blog. DIY Project Details: apartmenttherapy.Forums New posts Search forums.

Media New media New comments Search media. Russia- Land-Cruiser. Calendar New events. Log in Register. Search titles only. Word Count:. New posts. Search forums. Log in. Change style. Contact us. Close Menu. JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. DIY roll up canopy? Cant seem to find the link for it, Any one have it? Its the one in the PVC tube that you cut a hole along it for the canopy to roll up in Many thanks.

RHINO said:. LandCruiserPhil said:. What kind of PVC are you using that does not distort from the heat? WC came through again! A friend found this Thanks again all.

Last edited: Mar 1, Bump for this. I have made myself a canopy, It roll's up real nice but I cant seem to get it to unroll without alot of hastle, I even enlarged the opening to see if that will help, But it didnt, My issue is when unrolling it the next wrap of tarp wants to come out along with the outer most, I need to stuff it back in to pull it out, I only get a few inches before I need to stuff it all back in, I wonder if I have too heavy of a tarp, That being industrial grade.

diy roll up awning

Now I have yet to mount it on the vehicle, I wanted to see if I could manage it before I put it on, I am also doing it by myself, I wonder if it would be good to have one person keep a little tention on it to have a tighter wrap?!? Now im just rambling If any of you have any thought feel free to post up. Still if you have any thought I would love to hear them.

I would think that if you had a good deal of tension on the tarp when you rolled it up that would make a great deal of difference. Then the wrap would be nice and tight and you wouldn't get the tarp wraping on its self. How about some pics of your DYI canopy?Hurricane Ike hit us in and knocked out power for a few days.

I made this awning in attempt to keep it cooler inside by blocking the radiant sun energy. Indeed, it was about 3 degrees cooler inside with the awning than without the awning. After the power was restored this awning served to lower the energy bill.

I did not measure that, however I'm sure it did. Here's how I made it and what I would do differently next time Did you use this instructable in your classroom? Add a Teacher Note to share how you incorporated it into your lesson. Start by making the frame. Visit your local Home Depot or Lowes. The amount of pipe depends on the width of your window. Mine window was about 5' wide, so a 6' wide frame was selected.

The DIY Retractable Canopy

A main reason 6' was chosen -- I'll say this now -- is that the awning material canvas drop cloth is available in a 6' width. I would not make the awning much bigger than this without more frame support structures. A 3' gap like mine is about the maximum I would recommend. I base this on having watched how it handled windy days. You can dry-fit parts for now. The awning material is a 6'x9' canvas drop cloth.

How to Restring an Awning

This is the cheapest canvas drop cloth I could find. The 6' width fits the 5' window and window frame nicely. Maybe I was lucky here -- you need to measure your own window frame to be sure there are flat places to mount the awning. So I wanted a little flap to overhang from the front of the awning. Your choice if you don't.

diy roll up awning

Form the drop cloth into an inside-out loop as shown. The drop cloth has a plastic backing; this should be facing out.

If you're good with a sewing machine, great! I'm not. I took this to a neighborhood alterations place. When done, you can invert it to canvas-side out. Dry-fit the frame and slide the canvas over the top.

Adjust the fittings to make sure the canvas is taut.Three things can make a roll-up awning look bad. The results, however, are worthwhile as your awning will end up looking as good as new. Begin cleaning by rolling out the awing by 3 feet and secure. Mix up some mild detergent and warm water in a bucket. Whether you have an acrylic awning or a vinyl awning, the same method will work for both types of roll-up awning.

Dip the scrub brush in the detergent and water mix and scrub the mold or mildew stains on the awning. Allow the mix to stay on the awning for 5 minutes. Then, using the hose, rinse with clean water. Repeat the process until the mold or mildew stains have been removed. Keep rinsing with cold water. Repeat the scrubbing and rinsing technique until all the stains have been removed from this section. Keep going until the awning has been completely unrolled and cleaned. Keep the awning unrolled and allow it to dry in the sun.

This will help to prevent mold and mildew forming. If you have to roll up the awning during bad weather, as soon as the rain has passed unroll it again so it can dry. Rips in a roll-up awning make it look terrible. These need to be fixed, and not only for cosmetic reasons.

Any rip will only grow bigger over time, especially if you live in a windy area, as the wind will open the rip even further. You can buy awning tape that can close the rips. Cut an appropriate sized piece of awning tape. Have the awning rolled all the way out. The piece of tape should be 2 inches larger on all sides than the rip itself. The job will be easier if you have someone to help you and hold the two sides of the fabric together as you apply the tape.

The more tightly the awning pieces are held together the tighter the repair will be. With the sides in place, press the tape down firmly and then rub to give firm adhesion to the roll-up awning. If there are any special instructions on the package of awning tape, follow these precisely for the best results. We welcome your comments and suggestions. All information is provided "AS IS.